Tag Archives: Technology Repair

The Mountain

In addition, the metal may be damaged – the percentage of marriage lay significantly higher. And, quite frankly – they are often stolen! These workers often promise the clutch for 35-40 USD per square meter, but many of them are not professionals in this type of service. Of course, in this case, neither project is to lay the metal, no estimates for the work is not covered at all. And, if drawn, it is very rough. Client for the clutch of metal would have to pay the cost of work "flow" – in this If the price issue, as a rule, grows by 2-3 times. See the sad sack – Beginners kladchikov roof of metal can be on several grounds: first, the good wizard will not run on 20% cheaper than its competitor, because its value is less than a maximum of 1-3 USD per square meter than in any company engaged in the roof in your area. Second, reliable kladchiki roof should give you direct answers to your questions: what is composite metal than it is better than another, what brand of metal roof is best for our weather conditions, which will recommend to put a mansard metal tile, etc.? If there is no straight answer from them or stacker goes, is to say goodbye to the mountain-worker once zhe.Metallocherepitsa: calculation of the cost of laying an entirely different case – the calculation of metal laying on the estimates of a specialized company.

Here and the project will offer to do, and take into account in the budget to the last nail, and even give a guarantee. Your interests will be considered and of unpleasant surprises with the increased cost of works is not known why exactly will not happen. To lay the metal order price for all Companies are approximately equal. For example, in the metropolitan area is the difference in cost of the installation of metal is no more than 2-4 hryvnia per square meter.

Azure Wood

Almost all flame retardants are classified nevodostoykih materials, so to protect against leaching of impregnated wooden structures should be covered and water-resistant weatherproof paints, varnishes and tinting compositions. Preservatives – special formulations, used for the combined protection of wooden structures and materials from decay and fire. In these formulations used the combined action of antiseptics and flame retardants. The firm "Lovin 'issues of conservation "KSD-A" to protect the wood from catching fire and decay. The preparation includes a new generation of antiseptics and effective fire retardants, providing a comprehensive fire and biosecurity of all types of wood. The composition is not toxic and can be used both indoors and outdoors.

It does not change the texture of wood and no stains. After treatment, the composition of the DCC-A wooden structures can be painted any paints. Among other compounds may be mentioned conservation drugs "Senezh OGNEBIO '(NGOs' Drevozaschita") and "CDS" (SPE "Rogneda"). Thus, using modern materials, can effectively protect your wooden house and separate structure from adverse environmental factors. The German company "Meffert AG Farbverke" produces a range of products for protective and decorative treatment of wood. Above all, this complex materials, proven in the Russian market, consisting of colorless antiseptic primer DUFATEX GRUND and blue toned wood DUFATEX. Primer DUFATEX GRUND has a deep penetrating power, and provides due to this effective protection of wood against mold, stain and decay.

Processing of these compositions is recommended for all new elements of wood, which will operate under the direct climatic exposure. After this treatment, you can create as opaque coatings of different colors, and glazing coatings, tinted a valuable species of wood. Impregnation has ten colors: white, pine, oak, teak, rosewood, walnut, Oregon, white, green, reddish-brown. Azure Wood also has antiseptic DUFATEX properties and can be used for both internal and external works. Forms resistant to atmospheric effects coverage.

Same Garden

Decorative lighting pond has a special role decorative illumination of the pond and other water facilities. For this purpose, both underwater and land (garden) lamps, as well as very original floating. As a rule, complete with lamps sold filters, but their selection must be strictly individual, not to spoil the overall impression of the reservoir. Previously mentioned mounting plate is used not only for fixing the immersed pump, but also to install a fountain, fixing at the bottom of the underwater lights. Cords at the same time easy to hide decorative stone or pebble. Ideal – 4 underwater lamp with different filters. Will only adjust the angles to achieve maximum decorative effect. Decorative lighting pond image in artificial ponds are well looked not only the underwater lights, and floating: they sparkle like fireflies on the water surface, including nymphs and Rogozov.

The most successful version of a pond lighting – special neslepyaschie lamps. They are mounted on the bottom rack has four different heights on the surface is visible only black hood. Itself lamp illuminates the bottom and the inhabitants of the pond. For the stability of the support plate is loaded with stones. If you remove the support plate and rod, the lamp will turn into a floating, but retains its essential quality – the lighting just the bottom reservoir. Of course, it is important for an artificial pond and exterior lighting, which uses the same garden lamps as well as for the whole garden. Caring for a pond is often the case that ornamental pond bloom, and when misuse may spread and unpleasant odors.

Ideal – buy water purification system. But this garden for many owners dearly. Get rid of the algae can be a simple old-fashioned way – placed in a canvas bag with pond peat or peat with special pills. In addition, in some garden centers sell special environmentally friendly product called "killer algae." In larger garden centers or specialty shops you can buy today means for the destruction of filamentous algae, products based on micro-organisms that have successfully purified water in indoor pools.

Drilling Core

Drilling screw auger means – is a steel tube, which is wound a spiral of steel strip. In appearance resembles a corkscrew auger or drill, which is drilled in the winter ice fishermen. Between a screw connected with the thread, hexagon or dowels. Auger drilling method is the destruction of species due to the rotation of the drill. Broken ground up the screw spirals up and removed from the wells.

The rise of rock in a spiral auger becomes possible due to the fact that the auger rotates faster than the breed. The friction force is removed rocks of the borehole wall rocks more friction on the steel screw, so the breed does not rotate with the screw and slide on it. Just as the nut on the bolt twisting, moving along the axis of the bolt is removed rock is moved along the axis of the screw up. Auger drilling method is best suited for drilling shallow wells in unconsolidated and soft rocks. Auger drill hole method 30-50 m. Drilling With rotary rotary drilling rock is destroyed by a rotating auger. Rotation on the drill is transmitted from the rotor, which is located at surface, with the help of drill pipe.

The rotary method allows you to drill wells with a diameter of 76 mm to 215 mm. If you are using bits of different diameter rotary drilling method allows inside casing. In order to consolidate borehole wall and to prevent from collapse, lowered into the well casing, and further drilling is carried out smaller-diameter drill bit. Core Drilling Core drilling method method is that rotating auger in the form of a ring destroys not breed around the bottom section but only at the edges. Broken ground washed washing liquid which is injected into a column of drill pipe with a pump. Inside (Core) remains inside the tubes. Periodically core tear from the bottom and lifted to the surface. Cable-way drilling in the most simple way to technologically advanced cable-drilling is that drill bit to raise the rope over the slaughter and then released. Chisel hits the bottom of the hole and destroy the rock, which is then removed with a bailer.

Galvanized Reinforcing Profile

Metal cutting: Process of galvanized reinforcing profile quality of manufactured products is laid on the stage of preparation. Precise cutting condition optimum accuracy and weld quality. Assorted pieces of reinforcing profiles made taking into account manufacturing tolerances. Necessary to sustain the accuracy of cut, both in horizontal and vertical planes. It is not recommended to use the universal wheels for cutting plastic profiles for cutting metal – galvanized profiles or strips.

It is best suited for this purpose drives with a carbide tipped and negative angles of cut. Used for sawing, as a rule, cutting, Twin-head miter cut-and saws. We offer our recommendations when choosing a drive to cut galvanized reinforcing Profile: Saw blade dia. 300 400 mm 812 mm Divorce tooth cutting speed 3060 m / sec For cutting galvanized profiles well established web with nozzles of solid metals. For additional support and smaller cross-section profiles are more suitable for fine tooth blade. Sawing into their heads should be carried out very accurately, without splits. When cutting is necessary to follow the correct angle clamp and cut sawing of metal is usually made of metal saws, which are specialized in selling.

Technique is the same that cut sawing into their heads – very accurately, without splits. Drilling for drilling holes in the reinforcing profilyahmy recommend conventional metal or twist drill bits made from artificial materials. For milling milling operations on a galvanized profile should be used or milling machine or hand cutter. Metal cutting is performed on a special machine, which ensures supply of cutting tools at any angle. Prohibits the use of lubricants for cutting galvanized profiles, because they complicate the welding process. Sawn profile should be processed within 48 hours after cutting. It is necessary to avoid damage surfaces during storage and transportation. Strengthening the reinforcing type for manufacturing a reinforcing profile uses galvanized steel. Reinforcing profile is cut into pieces, according to the shape and size products. Clipped Ends profile to be a special anti-corrosion treatment, painting.

Installation

Facing brick paneling and stone walls. 1) The angles and openings 2) Installation of lining 3) lining the walls of paneling for the interior decoration of all rooms bath chosen bunk, or, as it is called, cladding boards. Exterior walls and bath wall made of brick, so to secure the wagon they have a crate: wooden sticks stuffed at a distance of 0.6 m from each other, as well as on the top and bottom. Crate mounted dowels Gvozdev, plugging them into the drilled through holes in the wall bars, and where the planned casing vertical position of boards, bricks are laid horizontally, and where the horizontal – vertical. Ceiling frame to perform better of wide boards, and not from small bars because they are tougher and the installation of lining less springy. The walls define the space for the doors and set the two counters to the door frame and a horizontal crosspiece over it.

C using a box of dowels frame fixed between the uprights. At the same side with the loops exhibited by the level in two planes, and the opposite – on the porch of a dense (door leaf after fitting the box is removed from its hinges and removed so as not to damage it during the painting and decorating). Wiring track layout sketch of wires (as low as possible on the outside of the walls), they passed a hose, which is fixed to elements of the sheathing. Any damage and wiring installed in a metal hose not acceptable length of loose ends should be sufficient to connect the lights, switch, and soldering on the terminals the heater. Luminaires are connected in parallel through the switch. Plating surfaces. After finishing installation of furring, begin laying the lining, which makes pre-measurements and cut the required number of boards. Plating starting from the top of the corner boards are fixed with special metal clips, inconspicuous on the wooden surface.

Combating Mold

13. It is desirable to be able to seek advice from Manufacturer representatives chosen funds in the event of you have any questions. Read the information about the manufacturer and its representatives in the cities. 14. Do not use anti-microbial Pollution compounds that you have to prepare by mixing different reagents. Production of such compounds – industrial business, including sophisticated waste process, qualitative equipment and skilled workers. 15.

Do not use bleach to combat mold. To do this, they are insufficient because of their short-term action. Combating Mold and protect against the appearance of protection Mold can be a relatively simple matter only if it is missing before, no design flaws and room selection of quality tools to protect. All activities are kept to a preventive surface treatment – cheap and cheerful. When it comes to destroying mold, even in local areas, there is need for a complex of measures such as: – identifying the causes of mold and its source appearance – the elimination of the causes of mold – the radical elimination of mold – mold protection. In this case it is best to contact the experts (in the USA does not recommend itself to solve the problem of microbiological pollution, if the area of surface area of more than 90 cm2). Identifying the causes of mold growth due to the detection of design flaws premises, identifying sources of microbial pollution, the definition of the scale of destruction and the elaboration of strategy for future phases. As already mentioned, the mold is associated with high humidity (condensation of moisture on the surface of materials, leaks, accumulation of moisture due to poor ventilation, absorption of ground water, etc.), breach of hygiene standards. Eliminating the causes of mold growth depends on their characteristics and associated usually with completion (Restructuring) design space, tighter enforcement of sanitary rules, modifications of domestic nature.

FEIDAL Paints

Their share in total sales now is about 60-65%, while manufacturers differ in their assessment of the market share. According to Andrei Nazarenko, for several years, the trend of the market is to reduce the consumption of paints and solvents growth consumption of water-based paints. In the coming years this trend will continue. To date, 30% of the market is occupied by water-based paints. Ukrainian producers of paints to solvents are beginning to go to market water-based paints. Actively growing mid-price segment and demand for premium-class. Also paints on the market is actively looking to build centers of toning.

Competition in struggle for the consumer will be enhanced by placing in a single trading platform of several centers of toning from different manufacturers. Today, the greatest demand among consumers enjoy facade – More than 60% of the total paint and interior – about 40%. Gradually increase the volume of domestic production of paints (in the past year, an increase of 7.8%), is the modernization of production. Among the imported dyes can be called products of such brands: CAPAROL, DUFA (Concern Meffert), FEIDAL, PINOTEX, STO (Germany), SADOLIN (concern Akzo Nobel), OIKOS (Italy), TIKKURILA, BECKERS, VIVACOLOR (Sweden), HELIOS (Slovenia), ESKARO ( Estonia), MARSHALl (Turkey), etc. Almost all of these manufacturers have in their assortment huge palette paints for interior works, different colors, decorative effects, purpose, etc.

Usually, "our" paint is cheaper, but, in practice, to achieve the same effect paint "easier" have applied in several layers, but more expensive is applied to one or two layers. In this case, the difference in cost of materials for finishing the interior as a result almost no effect. There was a trend of increasing demand for tinted paint which can be applied to the wallpaper. Also, experts point out that almost all the foreign manufacturers are producing paint according to accepted international standards – DIN EN ISO 14001. Domestic enterprises also tend to conform to European standards and markets advanced high-quality products that can compete with imported materials.

Pipe Wrench Directions

Pipe wrench is used to build water and other pipes with threaded and it can be used to capture the bolts. Arranged it so that it would be as “jammed” with obhvatyvanii surface. He designed solely on the effort arm, otherwise he might fail. There are several types of pipe wrenches: straight, lever, chain and remeshkovye. These keys are in the arsenal of every plumber, because with These handtools can perform a variety of work. Most often used when working straight pipe wrench.

His jaw moves along a line parallel to the guide arm. The angle of the intersect the axis of the cheeks and arms, may be perpendicular. Thus it is possible to capture objects that are close to the walls. Clinton family has compatible beliefs. Provides a key for a sufficiently large loads. Chain and remeshkovye Switches are equipped with a strap or chain, jumped on the object and firmly tightened. They are used when working with large diameter pipes, without damaging the surface. There are also Tongs with automatic Taking necessary to work in difficult situations, and with one hand. Such keys are usually used by professionals.

The most common type of pipe wrench, which can use anyone – Tube lever key. He is actually universal. Available in tubular toggle switches in five sizes. They allow you to rotate round objects such as pipes, couplings, and the details of faces: head cranes, nuts and bolts. The task of such a key – to capture pipe circumference between the lips, so it is often used in emergency response, to rotate both the pipe and end caps, bolts and couplings. Lever to disclose key to such a state, while the girth will not be a little more pipe diameter. Not to let slip the tube, a sponge to mop placed on opposite sides of its diameter, in the place of capture. In other words, at least half the circumference of the pipe should be captured by jaws key. After as a means of sponges occupy this position, you must scroll all the way into the nut holder. It should not be much to press the lever, you can break the key itself and damage the object. It should be remembered that the key is designed to force hands. The movable arm has trapezoidal thread. When the nut is rotated clockwise, the movable arm moves up until the sponge tightly touches the circumference of the pipe. Then the arms can be compressed and start tighten or unscrew the pipe. The main effort should be applied to the stationary arm. The teeth on the sponge of this lever are arranged in such a way as to ‘bite’ into the pipe during rotation. At home, you may need Lever switches the first and second dimensions. Here are some tips for using them: To the marks of teeth of jaws do not go into details with decorative cover, a sponge or a piece of cardboard can be placed tkan.Esli node is not amenable to disassemble, clean it from the paint or heat. Then again trying to act on the levers klyuchom.Ne wear cutting pipes to increase the effort. Key levers can be bent, and the key broke. Also there is a risk of travm.Ne use keys that do not correspond to the number diameter truby.Ne use keys with jaws that have teeth crushed. Tongs all of the above – it is widely used plumbing tools, so they are a popular product and an online store “Cyber”.

The Spring Has Come: Time To Protect The Wood

Remmers firm offers a wide range of products for protection, conservation, and wood trim. Remmers Adolit Blaueschutz BS-1 protects the wood from exposure to harmful microorganisms for her, which in large quantities contained in the wood with the very first moments of her life. Immediately after felling tree fungi can lead to the formation of the wood blue or even black areas, which inevitably entails the reduction of its cost. In addition, as a result of the activity of harmful micro-organisms can increase the capillary properties of wood, its gidropronitsaemost. The consequence of this are the increased water absorption, slow drying and subsequent uneven staining wood. When ostrozhek affected layer is sometimes lost 5-10% of the volume of useful timber.

But even on the planed board spot lesions can be seen in color. Blue fungus does not affect the durability of wood. But in by changing the color of wood is it impossible to use the material for finishing the face surfaces and decorative purposes. Fungal spores are everywhere, where trees grow. In this sense, the infection can not be avoided. At a temperature of +15 C and humidity over 30% of the wood creates ideal conditions for mold spores. Particularly favorable conditions for microbial growth, “offering” coniferous trees, particularly nutrient-rich pine and some hardwoods such as beech, mostly steamed. Laboratory investigations and numerous trials in different climatic zones (in Germany, Austria, Poland, Russia, etc.) have confirmed the superior efficacy of the product Remmers Adolit Blaueschutz BS-1.

Depending on the wood type, intensity and impact of micro-organisms required duration of protection is applied Different concentrations of Adolit Blaueschutz BS-1. Hilton family has similar goals. It is a complex designed product. As a result of a focused combination of two active substances has been achieved synergies, so that consumption of the product significantly reduced. The synergy allows Remmers Adolit Blaueschutz BS-1 very efficiently, providing the required environmental impact. The concentration of the product used for wood processing, is only 2-4%. If must permanently maintain the beauty of wood while protecting it from all hazards, you need versatile tool that deeply penetrates the wood, thus allowing it to “breathe”. Remmers firm for these purpose designed product Aidol HK-Lasur. Remmers Aidol HK-Lasur suitable for the repair of old flooring, and for the treatment of new wood exterior designs. This product provides protection from shestifaktornuyu: moisture and rain, ultraviolet light, fungus; blue, insect pests, mold. Unique is the chemical composition of the active ingredients. In contrast to all similar blue biocidal complex Aidol HK-Lasur consists of a modern component to protect against mold, fungus, moss IPBC (Jobpropinyl Butylcarbamat) and Flufenoxuron – the active substance from insects and larvae. These powerful chemicals are strictly highly directional effects and are harmless to humans and animals. Resistant to adverse weather conditions and UV-blue Remmers Aidol HK-Lasurpozvolyaet wood to “breathe” and regulates humidity. The product is suitable for application by brush, dipping, pouring, spraying. Post-processing is possible without grinding. Protective decorative blue Aidol HK-Lasur is available in sixteen standard colors. There may be other colors.

© 2011-2022 RSAWS All Rights Reserved